LED Starlight Set 156x5m Fiber Optic
239,90 € sis. ALV 24%
- Suomen suosituin LED-tähtitaivas
- Parasta laatua
- Näyttävä kokonaisuus
- Ripaus luksusta
- Märkiin ja kuiviin tiloihin
LED Starlight Set 156x5m Fiber Optic
Starlight fiber optic set with USA CREE XP-G LED. LED starlight sets from us with over 10 years’ experience. Contact us by email or phone and we can give you tips and tricks. Finnish and/or English instruction manual included in the package. Free shipping for this product. Discount coupon not applicable for this product.
Remote controller included, with which you can start/pause the twinkle effect, dim/brighten the lights and turn them on/off. Can be installed so that it possible to turn on/off from a light switch. Dimming and twinkle effect work only with the remote controller, but it is not necessary to configure them every time. You can set a desired configuration and put the remote controller in a cabinet. Memory function keeps the same settings when using a wall mounted light switch. If you like, you can replace the default twinkle wheel with a 6-color twinkle wheel, which will give your starlight set different colors. You can pause the twinkle wheel on a certain color.
Default crystal is a diamond-shaped nr. 1 (check the product image). If you like, you can also pick type 2 or 3 or make a mix of each. If you would like a certain amount of certain crystals etc. let us know in the comment section of your order. Without comments the package is provided with crystal nr. 1.
- Optical fibers (156 pcs)
- Fiber optic projector
- 12V DC socket plug power source
- Decorative crystals for fibers (16 pcs)
- Fitting piece to connect the crystal and fiber.
- Twinkle wheel
- RF remote controller
- Instruction manual
- 1 mm drill bits 10 pcs
- 1,5 mm drill bits 2 pcs
Good to know:
Q: Can fibers be installed in sauna ceiling?
Answer: Yes they can. Above the sauna heater/stove it is recommended to cover the fibers either with crystals or sauna stove lens. When crystals are used, the weakest link is the glue used in the crystal and it is heat resistant up to 130°C. The crystal can withstand pretty high temperatures. The crystals are originally meant for the thicker 1,5 mm fibers. If you’d like extra crystals you can also use the thinner fibers. You can put for example one, two or even three of those in one crystal. The hole size of the fitting piece needs to be increased if you put more fibers in but that should be no problem for a handyman.
Q: Are fibers cutable?
A: Yes they are and it is common to cut some or all of them. During installation bring the fibers 10-15 cm below the ceiling paneling and apply a little bit of glue on the topside of the panel around the fiber. Finally, cut the fibers on level with ceiling by using round-cutting cutter (flat cutters tend to press and damage the end of especially the thicker fibers). It is usually recommendable to leave the fibers somewhat evenly long for the whole project so that the starlit sky looks evenly lit. 1 meter long fibers are brighter than 5 meter long fibers.
Information on product images:
The sauna in the first image is 1,8 m x 2,4 m = 4,3 m2 and there is a 100-piece fiber set in the sauna.
You can find more information about the project on an article made by Iltalehti 🙂
Bedroom starlit sky has been made with this 156-kuituisella set 🙂
Optical fiber is either an end-to-end or a side-lighting product. End-to-end lighting models have a coating that directs the light towards the other end of the fiber. Side-lighting models do not have this coating which is why the fibers will also light up from the side. Side-lighting fibers are used for example in situations such as when lighting curtains are created with optical fibers. Starlight sets by Ledtek are end-to-end lighting models. On the enchanting video below you can see how the fibers direct the light towards the other end. The video has been recorded in Finland and there are 316 fibers in this particular project.